Yokogawa FVX110 Bedienungsanleitung Seite 22
- Seite / 164
- Inhaltsverzeichnis
- FEHLERBEHEBUNG
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
<2. Handling Cautions>
2-12
IM 01S01C01-01EN
Note 2. Electrical Data
• Supply voltage: 32 V dc max.
Output current: 15 mA dc
Note 3. Installation
• All wiring shall comply with local installation
requirements.
• The cable entry devices shall be of a certied
ameproof type, suitable for the conditions of
use.
Note 4. Operation
• Keep the “WARNING” label attached to the
indicator.
WARNING: AFTER DE-ENERGIZING,
DELAY 5 MINUTES BEFORE OPENING.
WHEN THE AMBIENT TEMP.≥65ºC, USE
HEAT-RESISTING CABLES≥90ºC.
• Take care not to generate mechanical
sparking when accessing the instrument and
peripheral devices in hazardous location.
Note 5. Maintenance and Repair
• The instrument modication or part
replacement by other than an authorized
representative of Yokogawa Electric
Corporation is prohibited and will void KEMA
Flameproof Certication.
(2) Electrical Connection
A mark indicating the electrical connection type is
stamped near the electrical connection port. These
marks are as follows.
F0211.ai
Location of the mark
ISO M20×1.5 female
ANSI 1/2 NPT female
MarkingScrew Size
A or W
M
(3) Installation
WARNING
• All wiring shall comply with local installation
requirements and the local electrical code.
• There is no need for a conduit seal in
Division 1 and Division 2 hazardous
locations because this product is sealed at
the factory.
The grounding terminals are located on the inside
and outside of the terminal area.
Connect the cable to grounding terminal in
accordance with wiring procedure 1) or 2).
2) Internal grounding
terminal
1) External grounding
terminal
F0212.ai
Wiring Procedure for Grounding Terminals
(4) Operation
WARNING
• OPEN CIRCUIT BEFORE REMOVING
COVER. INSTALL IN ACCORDANCE WITH
THIS USER’S MANUAL
• Take care not to generate mechanical
sparking when accessing the instrument and
peripheral devices in a hazardous location.
(5) Maintenance and Repair
WARNING
The instrument modication or part replacement
by other than an authorized Representative of
Yokogawa Electric Corporation is prohibited and
will void the certication.
- Fieldbus Segment Indicator 1
- Contents 2
- 1. Introduction 8
- 1.2 Warranty 9
- 1.3 ATEX Documentation 10
- 2. Handling Cautions 11
- Protected Instrument 13
- Terminal 15
- 2.8.2 CSA Certication 17
- Location of the mark 22
- 2) Internal grounding 22
- 1) External grounding 22
- 2.8.4 IECEx Certication 23
- 3. Component Names 25
- 4. About Fieldbus 26
- 5. Installation 28
- 5.3 Wiring 29
- 5.4 Grounding 30
- 5.5 Connection of Devices 30
- 5.6 Host Setting 31
- 5.7 Bus Power ON 32
- 6. Conguration 34
- 6.2 Network Denition 35
- 6.3 Denition of Combining 36
- Function Blocks 36
- 6.4 Setting of Tags and 37
- Addresses 37
- 6.5 Communication Setting 37
- 0x1: System/network 38
- 0x1234: Function block 38
- 6.6 Block Setting 39
- 6.6.2 Trend Object 40
- 6.6.3 View Object 40
- <6. Conguration> 41
- 7.3.2 Operating mode 44
- 7.3.1 Function Outline 44
- Quality Sub-status 46
- 7.3.5 Indicator settings 47
- Figure 7.4 Sub Tag settings 48
- (switching displays) 62
- 9. In-Process Operation 64
- 9.3 Device Diagnostic 67
- Simulation Function 67
- 10. Maintenance 69
- Assembly 70
- 11. Device Information 71
- 12. Parameter Lists 74
- 12.2 LCD Transducer Block 77
- 13. General Specications 85
- 13.2 Physical Specications 86
- 13.3 Model and Sufx Codes 86
- 13.5 Optional Specications 88
- 13.6 Dimensions 89
- A1.1 Schematic Diagram of 90
- Signal Characterizer Block 90
- A1.2 Input Section 91
- FA0103.ai 92
- A1.5.1 Input Compensation 95
- A1.5.3 Backward Control 96
- Figure A2.1 Integrator Block 97
- A2.2 Input Process Section 98
- A2.3 Adder 99
- A2.4 Integrator 100
- A2.5 Output Process 101
- IM 01S01C01-01EN 102
- A2.6 Reset 103
- A2.6.2 Reset Timing 104
- A2.6.3 Reset Process 104
- Figure A3.1 IS Block 108
- A3.2 Input Section 110
- A3.2.2 MIN_GOOD Handling 111
- A3.3 Selection 112
- A3.3.2 SELECTION Handling 113
- Figure A3.5 Example (4) 114
- Figure A3.6 Example (5) 115
- Figure A3.7 Example (6) 116
- Figure A3.8 Example (7) 117
- Figure A3.9 Example (8) 118
- A3.4 Output Processing 119
- A3.4.2 OUT Processing 120
- A3.4.3 STATUS_OPTS 121
- FA0311.ai 123
- A4.2 Input Section 125
- A4.2.3 INPUT_OPTS 126
- Inputs and PV 126
- A4.3 ComputationSection 127
- A4.4 OutputSection 127
- AUTO MAN AUTO 128
- BAL_TIME 128
- Appendix 5. PID Block 132
- A5.3 Parameters of PID Block 133
- A5.4 PID Computation Details 136
- A5.5 Control Output 136
- A5.7 Control Action Bypass 137
- A5.8 Feed-forward 137
- A5.9 Block Modes 137
- A5.10 Bumpless Transfer 138
- A5.11 Setpoint Limiters 138
- Fallback (IMan) 139
- A5.15 Manual Fallback 140
- A5.16 Auto Fallback 140
- A5.17 Mode Shedding upon 140
- Computer Failure 140
- A5.18 Alarms 141
- A5.19 Example of Block 141
- Connections 141
- A5.20 View Object for PID 142
- Function Block 142
- (MAO) Block 143
- A6.2 Block Mode 144
- A6.3 Fault State 145
- A6.4 Status Transitions 146
- A6.5 Parameter list display 146
- A7.1 Link Active Scheduler 148
- A7.2 Link Master 148
- A7.3 Transfer of LAS 149
- A7.4 LM Functions 150
- A7.5 LM Parameters 151
- SCHEDULE_LIST_ 152
- CHARACTERISTICS_ 152
- A7.6 FAQs 155
- Field Device 159
- A8.7 Troubleshooting 159
- Software Download 161
- Relating to Software Download 162
- IMPORTANT 162
- (3) DOMAIN_HEADER 163
- Revision Information 164
Verwandte Produkte und Handbücher für Sensoren Yokogawa FVX110
Sensoren Yokogawa HIMHART Bedienungsanleitung
(27 Seiten)
(27 Seiten)
Sensoren Yokogawa EXA SC202 2-Wire Conductivity Transmitter/Analyzer Bedienungsanleitung
(113 Seiten)
(113 Seiten)
Sensoren Yokogawa EXA SC202 2-Wire Conductivity Transmitter/Analyzer Bedienungsanleitung
(72 Seiten)
(72 Seiten)
Sensoren Yokogawa EXA SC202 2-Wire Conductivity Transmitter/Analyzer Bedienungsanleitung
(72 Seiten)
(72 Seiten)
Sensoren Yokogawa EXA ISC202 2-wire Conductivity Transmitter/Analyze Bedienungsanleitung
(64 Seiten)
(64 Seiten)
Sensoren Yokogawa EXAxt SC450 4-Wire Analyzer for Conductivity/Resis Bedienungsanleitung
(68 Seiten)
(68 Seiten)
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.078 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern