Yokogawa FVX110 Bedienungsanleitung Seite 110
- Seite / 164
- Inhaltsverzeichnis
- FEHLERBEHEBUNG
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
<Appendix 3. Input Selector (IS) Block>
A3-3
IM 01S01C01-01EN
A3.2 Input Section
A3.2.1 Mode Handling
The Input Selector block’s operations are determined by the mode (parameter name: MODE_BLK). The
following describes operations in each mode.
Supported Mode Role
O/S
(Out of Service)
• System-stopped status.
• Allows you to make changes to conguration.
Man •
If you do not want to output the value and status from IN or if the
value or status thus output is not preferable, you can manually
transmit the value to OUT.
Auto •
Automatic system operation status.
Valid Input
When the following conditions are satised, the value of IN_n becomes valid.
1) The QUALITY in each status of IN_n is either Good (NC), Good (C), or Uncertain*
1, 3
.
2) The values of DISABLE_n corresponding to each IN_n are OFF and the QUALITY in the status of which is
either Good (NC), Good (C), or Uncertain*
1, 2
.
3) The number of inputs that are “good” is greater than the value of MIN_GOOD*
4
.
Note:
*1: Uncertain is applicable when “Use Uncertain as Good” is selected in the STATUS_OPTS parameter.
*2: If the status of DISABLE_n is Bad or Uncertain, its quality is lower so that the status of IN_n is also dened as lower quality. When
DISABLE_n is ON, the value of IN_n becomes invalid. For the priority of DISABLE_n is higher than that of IN_n.
Status in SELECT_TYPE except OP_SELECT
QUALITY of DISABLE / IN Status IN
Good (NC) Valid
Good (C) Valid
Uncertain
*1
Valid
Uncertain Invalid
Bad Invalid
Condition: The number of inputs that are “good” is greater than the value of MIN_GOOD.
*3: Priority of IN_n when the same value is input.
Priority
1:Highest
8:Lowest
Input
1 IN_1
2 IN_2
3 IN_3
4 IN_4
5 IN_5
6 IN_6
7 IN_7
8 IN_8
*4: Refer to A3.2.2 for the details of MIN_GOOD.
- Fieldbus Segment Indicator 1
- Contents 2
- 1. Introduction 8
- 1.2 Warranty 9
- 1.3 ATEX Documentation 10
- 2. Handling Cautions 11
- Protected Instrument 13
- Terminal 15
- 2.8.2 CSA Certication 17
- Location of the mark 22
- 2) Internal grounding 22
- 1) External grounding 22
- 2.8.4 IECEx Certication 23
- 3. Component Names 25
- 4. About Fieldbus 26
- 5. Installation 28
- 5.3 Wiring 29
- 5.4 Grounding 30
- 5.5 Connection of Devices 30
- 5.6 Host Setting 31
- 5.7 Bus Power ON 32
- 6. Conguration 34
- 6.2 Network Denition 35
- 6.3 Denition of Combining 36
- Function Blocks 36
- 6.4 Setting of Tags and 37
- Addresses 37
- 6.5 Communication Setting 37
- 0x1: System/network 38
- 0x1234: Function block 38
- 6.6 Block Setting 39
- 6.6.2 Trend Object 40
- 6.6.3 View Object 40
- <6. Conguration> 41
- 7.3.2 Operating mode 44
- 7.3.1 Function Outline 44
- Quality Sub-status 46
- 7.3.5 Indicator settings 47
- Figure 7.4 Sub Tag settings 48
- (switching displays) 62
- 9. In-Process Operation 64
- 9.3 Device Diagnostic 67
- Simulation Function 67
- 10. Maintenance 69
- Assembly 70
- 11. Device Information 71
- 12. Parameter Lists 74
- 12.2 LCD Transducer Block 77
- 13. General Specications 85
- 13.2 Physical Specications 86
- 13.3 Model and Sufx Codes 86
- 13.5 Optional Specications 88
- 13.6 Dimensions 89
- A1.1 Schematic Diagram of 90
- Signal Characterizer Block 90
- A1.2 Input Section 91
- FA0103.ai 92
- A1.5.1 Input Compensation 95
- A1.5.3 Backward Control 96
- Figure A2.1 Integrator Block 97
- A2.2 Input Process Section 98
- A2.3 Adder 99
- A2.4 Integrator 100
- A2.5 Output Process 101
- IM 01S01C01-01EN 102
- A2.6 Reset 103
- A2.6.2 Reset Timing 104
- A2.6.3 Reset Process 104
- Figure A3.1 IS Block 108
- A3.2 Input Section 110
- A3.2.2 MIN_GOOD Handling 111
- A3.3 Selection 112
- A3.3.2 SELECTION Handling 113
- Figure A3.5 Example (4) 114
- Figure A3.6 Example (5) 115
- Figure A3.7 Example (6) 116
- Figure A3.8 Example (7) 117
- Figure A3.9 Example (8) 118
- A3.4 Output Processing 119
- A3.4.2 OUT Processing 120
- A3.4.3 STATUS_OPTS 121
- FA0311.ai 123
- A4.2 Input Section 125
- A4.2.3 INPUT_OPTS 126
- Inputs and PV 126
- A4.3 ComputationSection 127
- A4.4 OutputSection 127
- AUTO MAN AUTO 128
- BAL_TIME 128
- Appendix 5. PID Block 132
- A5.3 Parameters of PID Block 133
- A5.4 PID Computation Details 136
- A5.5 Control Output 136
- A5.7 Control Action Bypass 137
- A5.8 Feed-forward 137
- A5.9 Block Modes 137
- A5.10 Bumpless Transfer 138
- A5.11 Setpoint Limiters 138
- Fallback (IMan) 139
- A5.15 Manual Fallback 140
- A5.16 Auto Fallback 140
- A5.17 Mode Shedding upon 140
- Computer Failure 140
- A5.18 Alarms 141
- A5.19 Example of Block 141
- Connections 141
- A5.20 View Object for PID 142
- Function Block 142
- (MAO) Block 143
- A6.2 Block Mode 144
- A6.3 Fault State 145
- A6.4 Status Transitions 146
- A6.5 Parameter list display 146
- A7.1 Link Active Scheduler 148
- A7.2 Link Master 148
- A7.3 Transfer of LAS 149
- A7.4 LM Functions 150
- A7.5 LM Parameters 151
- SCHEDULE_LIST_ 152
- CHARACTERISTICS_ 152
- A7.6 FAQs 155
- Field Device 159
- A8.7 Troubleshooting 159
- Software Download 161
- Relating to Software Download 162
- IMPORTANT 162
- (3) DOMAIN_HEADER 163
- Revision Information 164
Verwandte Produkte und Handbücher für Sensoren Yokogawa FVX110
Sensoren Yokogawa HIMHART Bedienungsanleitung
(27 Seiten)
(27 Seiten)
Sensoren Yokogawa EXA SC202 2-Wire Conductivity Transmitter/Analyzer Bedienungsanleitung
(113 Seiten)
(113 Seiten)
Sensoren Yokogawa EXA SC202 2-Wire Conductivity Transmitter/Analyzer Bedienungsanleitung
(72 Seiten)
(72 Seiten)
Sensoren Yokogawa EXA SC202 2-Wire Conductivity Transmitter/Analyzer Bedienungsanleitung
(72 Seiten)
(72 Seiten)
Sensoren Yokogawa EXA ISC202 2-wire Conductivity Transmitter/Analyze Bedienungsanleitung
(64 Seiten)
(64 Seiten)
Sensoren Yokogawa EXAxt SC450 4-Wire Analyzer for Conductivity/Resis Bedienungsanleitung
(68 Seiten)
(68 Seiten)
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.088 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern