Yokogawa DR240 Bedienungsanleitung Seite 93
- Seite / 121
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
7-17
IM DR231-11E
Output Format
7
Data status
Outputs the status of the report computation result. The sum of the top numbers of the
phenomena from the following items is output.
1H: Detected over-limit data during measurement
2H: Detected special data during sampling
4H: Power failure occurred during computation
80H: Numerical data valid
Output data
Depending on the type of report computation, the results are output in the following order.
Computation type: INST (instantaneous value)
G1 to Gn, data H1 to data Hn: Instantaneous value during report creation
l1 to ln, data J1 to data Jn: Meaningless data
K1 to Kn, data L1 to Ln: Meaningless data
Computation type: AVE (average)
G1 to Gn, data H1 to data Hn:
Hourly report: Average value of the measured data over 1 hour
Dayly report: Average value of the measured data over 1 day
Monthly report: Average value of the measured data over 1 month
l1 to ln, data J1 to data Jn:
Hourly report: Minimum value of the measured data over 1 hour
Dayly report: Minimum value of the measured data over 1 day
Monthly report: Minimum value of the measured data over 1 month
K1 to Kn, data L1 to Ln:
Hourly report: Maximum value of the measured data over 1 hour
Dayly report: Maximum value of the measured data over 1 day
Monthly report: Maximum value of the measured data over 1 month
Computation type: SUM (sum)
G1 to Gn, data H1 to data Hn:
Hourly report: Summed value of the measured data over 1 hour
Dayly report: Summed value of the measured data over 1 day
Monthly report: Summed value of the measured data over 1 month
l1 to ln, data J1 to data Jn: Total of the summed values since the start of the report
K1 to Kn, data L1 to Ln: Meaningless data
If the data is abnormal, the following value is output at the mantissa of the computed data.
7FFF7FFFH: Positive over-limit data
80018001H: Negative over-limit data
80028002H: Measurement range setting skips
80038003H: The specified channel is not connected
80048004H: Data error
80058005H: Data output not possible
Note
• The mantissa of the data length, extension number, power failure information and data can be output from either the
upper or the lower byte with the BO command.
• The report channels set to OFF are output in the following way.
Type of report computation result: 00H (invalid)
Data status: Meaningless data
The exponent and mantissa of the data: Meaningless data
7.13 Report Output Format
- Communication Interface 1
- Instruction Manual 1
- Introduction 2
- Trademark 2
- TABLE OF CONTENTS 4
- CHAPTER 7 OUTPUT FORMAT 6
- CHAPTER 8 SAMPLE PROGRAM 6
- APPENDIX 6
- Rotary switch with 9
- Address is the numeral 9
- 1.3 Specifications 10
- Listener and Talker Functions 11
- Status Byte Format 12
- 2.2 Specifications 13
- 2.5 Communication Data Format 18
- 3.2 Specifications 21
- Cable Used 22
- Connecting the Cable 22
- Converter 25
- Terminator 25
- Minimum Response Time 26
- 3.4 Communication Data Format 27
- Procedure 28
- Connecting to the Network 30
- About the Ports 30
- Communication Operation 31
- 4.2 Specifications 32
- Setting the Dip Switch 33
- LED Indication 33
- 4.4 Setting the IP Address 35
- Configuring from the PC 36
- 4.5 Connection Methods 37
- DR's IP address 42
- <Enter> 42
- 4.9 Setting the T imeout 43
- 5.1 Command Format 44
- 5.2 Command Syntax 46
- ●Stand alone model (DR130) 47
- 5.4 Command List 48
- Control Execution Command 49
- Output Request Command 49
- 5.4 Command List 49
- 5.5 Input Range Parameter 50
- RATE RATE 0 to 30000 52
- GATE GATE 0 to 30000 52
- 5.6 ASCII Code Table 54
- 6.1 Setting the Input 55
- Setting Scaling 56
- 6.1 Setting the Input 56
- SN Sets the scaling unit 57
- XQ Sets the filter 57
- 6.2 Setting Alarms 58
- 6.3 Setting the Display 59
- 6.4 Setting the Recording 60
- Commands 61
- Message setting 61
- Message copy 61
- XC Sets dot printing colors 63
- 6.5 Other Settings 64
- XB Sets the burnout 68
- 6.6 Control and Execution 71
- RS Reconstruct the system 74
- RC Initialize the set values 74
- 6.7 Data Output Request 75
- 7.1 Functions as Talker 77
- (ASCII code) 78
- (Binary code) 79
- Position 83
- ±DDDDDE-EpCrLf 87
- For Measured Data 90
- For Computed Data 90
- 7.13 Report Output Format 92
- Daily Report 94
- 7.13 Report Output Format 94
- Monthly Report 96
- 8.1 GP-IB Sample Programs 99
- IM DR231-11E 100
- 8.2 RS-232-C Sample Programs 102
- Output the Setting Data 105
- Sample Program 107
- 8.4 Ethernet Program 111
- 8.4 Ethernet Program 112
- App.1 Computing Equation 113
- Computation start 115
- Computation stop 115
- Computation clear & start 115
- Computed data 116
- Command Index 120
Verwandte Produkte und Handbücher für Sensoren Yokogawa DR240
Sensoren Yokogawa µR20000 Bedienungsanleitung
(263 Seiten)
(263 Seiten)
Sensoren Yokogawa DR240 Bedienungsanleitung
(293 Seiten)
(293 Seiten)
Sensoren Yokogawa JUXTA VJCE Bedienungsanleitung
(10 Seiten)
(10 Seiten)
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.049 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern