Yokogawa DR240 Bedienungsanleitung PDF herunterladen (Seite 71)

6-17

IM DR231-11E

Commands

6

6.6 Control and Execution

Command

PS Starts or stops recording.

Mode Operation mode

Setting PSp1<terminator>

p1 0 Recording starts.

1 Recording stops.

MP Starts or stops manual printing.

Mode Operation mode

Setting MPp1<terminator>

p1 0 Manual printing starts.

1 Manual printing stops.

Example Start manual printing.

MP0

LS Starts or stops list printing.

Mode Operation mode

Setting LSp1<terminator>

p1 0 List printing starts.

1 List printing stops.

Example Start list printing.

LS0

HD Starts or stops header printing.

Mode Operation mode

Setting HDp1<terminator>

p1 0 Header printing starts.

1 Header printing stops.

Example Start header printing.

HD0

SU Starts or stops setup list printing.

Mode Operation mode

Setting SUp1<terminator>

p1 0 Setup list printing starts.

1 Setup list printing stops.

Example Start setup list printing.

SU0

MS Starts message printing.

Mode Operation mode

Setting MSp1<terminator>

p1 01 to 20 (message number)

Example Start printing message No. 5.

MS05

AK Confirms the current alarm status.

Mode Operation mode

Setting AKp1<terminator>

p1 0 Confirms the current alarm status.

Example Confirm the current alarm status.

AK0

AR Resets an alarm.

Mode Operation mode

Setting ARp1<terminator>

p1 0 The alarm is reset.

Example Reset the alarm.

AR0

IR Resets the timer.

Mode Operation mode

Setting IRp1<terminator>

p1 0 The timer is reset.

Example Reset the timer.

IR0

AC Clears the alarm buffer.

Mode Operation mode

Setting ACp1<terminator>

p1 0 The alarm buffer is cleared.

Example Clear the alarm buffer.

AC0

MC Clears the message buffer.

Mode Operation mode

Setting MCp1<terminator>

p1 0 The message buffer is cleared.

Example Clear the message buffer.

MC0

EX Computation start/stop, restart of

computed data after they are cleared,

and release of statuses after

completing measurement.

Mode Operation mode

Setting EXp1<terminator>

p1 Computation start/stop, restart of computed

data after they are cleared, and execution of

releasing statuses after completing

measurement.

0: Computation start

1: Computation stop

2: Restart of computed data after they are

cleared

3: Computed data clear

4: Release of statuses after completing

measurement

Example Start the computation.

EX0

Comments • This command is effective only with the optional

computation functions or a floppy disk drive

function or with a pulse module installed.

• If MATH is set for level action in the event/action,

a computation start/stop/start after clearing the

computed data cannot be done using EX

command.

• This command is not executable during the

saving/reading of setup data.

MW Stores the measured data/computed

data on a RAM disk.

Mode Operation mode

Setting MWp1, p2, p3, p4, p5<terminator>

p1 Retention mode

DIRECT Data storage starts immediately

after sending an MW command.

TRIGER Data storage starts after a trigger

signal is generated.

REPEAT Specified data are repeated for

storage each time the trigger

signal is generated.

p2 File name (up to eight characters for other

than REPEAT, up to five characters for

REPEAT)

p3 Retention interval

INTVL Data are stored at measurement

intervals.

1 min/2 min/5 min/10 min

Data are stored at specified

intervals.

6.6 Control and Execution Command

1 2 ... 66 67 68 69 70 71 72 73 74 75 76 ... 120 121

Kommentare zu diesen Handbüchern

Keine Kommentare