Yokogawa DR240 Bedienungsanleitung Seite 27
- Seite / 293
- Inhaltsverzeichnis
- FEHLERBEHEBUNG
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
2-1
IM DR232-01E
2
Functions
2.1 Display Functions
The inter-active front panel display consists of three rows. The first row is the main display, and
the second and third row are sub-display 1 and 2 respectively.
Monitor Mode and Status Display
Monitor Mode
• Auto Mode
This mode can be set for the main display, sub-display 1 and sub-display 2. Measurement
values of all channels will be consecutively displayed with update interval.
• Manual Mode
This mode can be set for the main display, sub-display 1 and sub-display 2. Measurement
values of a single channel will be displayed. The display update interval is the same as the
measurement interval (refer to page 2-4).
• Manual Mode
This mode can be set for the main display. When choosing this display, the measurement values
of 5 consecutive channels will be displayed as a page using also sub-display 1 and 2. The
display update interval is the same as the measurement interval (refer to page 2-4).
• Alarm Search Mode
This mode can be set for the main display, sub-display 1 and sub-display 2. Channels at which
an alarm occurred will be searched for and their measurement values displayed. The display
update interval is 2 seconds.
• Bargraph Mode
This mode can be set for sub-display 1. Measurement values which are shown on the main
display will be shown as a bargraph. The display update interval is the same as the interval of
the main display.
• Alarm Status Mode
This mode can be set for sub-display 1 and 2. The display will show per channel whether or not
an alarm occurred (refer to page 2-13). On one display the alarm status of a maximum of 30
channels can be monitored (depending on the number of input channels). The display update
interval is 0.5 seconds.
• Relay Status Mode
This mode can be set for sub-display 1 and 2. The display will show the operating status of
internal switches/alarm output relays (refer to page 2-13). On one display a maximum of 30
relay statuses can be monitored. The display update interval is 1 second.
• Clock Mode
This mode can only be set for sub-display 2. The current date and time are shown.
• Displaying the Selected Mode
To the right of sub-display 1 the currently selected display mode is shown for a specific
display.
Status Display
Indicators at the right side of the display will light up to show that recording is in progress (refer
to page 2-5), alarms are occuring (refer to page 2-13), keys are locked (refer to page 2-17) and
chart needs to be replaced (refer to page 2-18).
Remote/Local Status Display
The status of remote/local control will be show on sub-display 2. Keys cannot be operated in
remote control.
- Instruction 1
- DR232/DR242 1
- Hybrid Recorder 1
- (Expandable Type) 1
- Foreword 2
- Trademarks 2
- Revisions 2
- Main Unit DR232/DR242 4
- Subunit DS400/DS600 4
- Input Modules 5
- Standard Accessories 6
- Optional Accessories 7
- Optional Software 7
- How to Use this Manual 9
- IM DR232-01E 10
- Contents 11
- Chapter 14 Specifications 13
- List of Menus and Set-up Data 14
- Computation Settings 15
- Perform Printing 15
- Other Settings 15
- 1.1 About DARWIN 16
- 1.2 Product Overview 17
- Connection example 18
- 1.3 Names of Parts 19
- System Configuration 20
- 1.3 Names of Parts 20
- Subunit DS400 21
- Subunit DS600 21
- Input modules 21
- Wire clip 22
- Clamp terminal 22
- Pulse input module (DU600-11) 23
- I/O Terminal Modules 24
- Communication Module 24
- Extender Module/Extender Base 25
- 1.4 Floppy Disk 26
- 2.1 Display Functions 27
- Input Type 29
- Skipping Input Channels 29
- Scan Interval 30
- A/D Integration Time 30
- Input Filter 30
- 2.3 Recording Functions 31
- Recording Example 32
- Recording Format 33
- Recording Colors 34
- Recording Interval 34
- Recording Span 35
- Starting/Stopping Recording 35
- Recording Zone 35
- Scale Values 35
- Partially Expanded Recording 36
- Interpolation Function 36
- List Printout 37
- Manual Printout 38
- Header Printout 38
- Additional Printouts 38
- Set-Up List Printout 38
- Match Time Function 38
- 2.4 Alarm Function 39
- Alarm status 40
- Operation of 40
- Internal switch/ 40
- 001 H 10.000mV 41
- Left span:-2V 42
- (=left scale:-0.1A) 42
- Right span:2V 42
- (=Right scale:1.1A) 42
- 2.6 Other Functions 43
- NO C NC NO CNC NO C NC 44
- Safety Precautions 46
- General Handling Precautions 46
- 3.2 How to Install 47
- Rack Mounting Dementions 48
- Panel cutting dimensions 49
- M4 screws 50
- • Rack mounting 51
- 3.2 How to Install 51
- Connecting Method 52
- Modules Which Can be Used 52
- Install the chart 54
- Loading the Ribbon Cassette 56
- Red lever 1 57
- Red lever 2 57
- Ribbon cassette holder 57
- Ferrite core 59
- RS-232-C 60
- RS-422-A/RS-485 61
- Ethernet 63
- Extension Cables 64
- Connecting Procedure 64
- W WARNING 65
- Terminals 67
- Wiring Diagram 67
- Installation and Wiring 70
- • Four-gauge method 70
- Installing an Extension Base 73
- Power ON/OFF 75
- DC power terminal 77
- DC power 77
- Switching the Power ON/OFF 79
- SET=CLOCK 80
- 3.11 Countering Noise 81
- Propagation of Noise 82
- Frequency (Hz) 85
- Signal lines* 86
- Φ = strong 87
- Φ = weak 87
- The instrument 89
- 4.1 Using the AUTO Display 91
- V0.0467 H d 92
- 004d L 0.0926V 005 0.0824V 93
- 4.2 Using the MANUAL Display 94
- 4.3 Using the PAGE Display 96
- 003 0.0054V 004 0.0319V 97
- 004 H 0.0269V 005 RH 0.0248V 97
- 005 0.2108V 006 0.0951V 97
- - 1.5000> < 2.0000 99
- 004 0.0153V 005 0.0123V 99
- Sub-display 1 and 2 100
- 005 0.8210V 006 0.0095V 103
- Dec. 30. 95 13:16:19 103
- 001-10:VOLT/2V 104
- 001-10:SCL:VOLT/2V 107
- _ _ _ _ _ _ 108
- From the previous page 108
- Monitoring Channel 109
- Strain Input Channel 113
- 001-01:PULSE/RATE 116
- SET=SYSTEM 118
- 6.2 Setting the Chart Speed 121
- Expanded Recording 123
- Printout 125
- SET=ALARM_PR 127
- SET=SCALE_PR 129
- SET=MESSAGE 131
- Interpolation and Groups 133
- Printing in Logging Mode 135
- Header Printing 136
- 7.3 Starting Message Printing 137
- 7.4 Printing Set-up Lists 138
- 001–01:1/OFF 139
- SET=LOGIC 143
- To the next page 144
- From the following page 144
- To the previous page 144
- ACT=LEVL/REPORT 146
- Reset here 153
- Not reset 153
- Computed value 153
- Start computing Event 153
- 9.2 Copying 154
- TIMER_RESET 156
- ALM_BUF_CLEAR 158
- Signal Input 160
- 9.6 Summer/Winter Time 161
- SETUP=PRN_ADJ 162
- 10.2 Setting Recording Format 164
- SETUP=ALARM 168
- SETUP=RELAY 170
- Compensation 173
- 10.6 Setting Recording Colors 175
- 10.7 Setting Key Lock 176
- 10.8 Setting FUNC/FUNC3 Menu 178
- 10.8 Setting FUNC/FUNC3 Menu 179
- 10.9 Setting SET/SET3 Menu 181
- PANEL:MANUAL PR 182
- MANUAL PR=SET3 182
- PANEL:ALARM PR 182
- ALARM PR=SET3 182
- From previous page 183
- To previous page 183
- Terminating SET UP Menu 185
- °C or °F 186
- SETUP=REPORT 188
- (Main menu item) 189
- (Submenu items) 189
- SET=MEMORY 197
- (Main menu) 198
- Trigger (event) 200
- Data length (100%) 200
- MODEL=EXPANDABLE 204
- CHANNEL=201–60 204
- 11.3 Saving Set-up Data 205
- SETUP=FLOPY 206
- 11.4 Reading Set-up Data 207
- SETUP=FLOPPY 208
- 11.5 Copying a Data File 210
- 11.6 Copying in ASCII Format 212
- 11.7 Deleting a Data File 215
- SET=FLOPPY 219
- Relational operators 221
- Executing Computation 221
- Logical operators 221
- SET=MATH 224
- 12.3 Setting a Constant 227
- Computed data 228
- Stop Clear/start 228
- TLOG SUM 232
- Replacement Period 234
- 13.2 Replacing the Fuse 235
- 13.3 Troubleshooting 236
- 13.4 Error Codes 237
- Trouble-shooting 238
- 13.4 Error Codes 238
- 13.5 Calibration 239
- DC Voltage Generator 240
- Input terminal 240
- ADJUST MODE=DISPLAY 243
- 20mV ZERO=– 1 243
- * * * DISPLAY END * * * 243
- ADJUST MODE=END 244
- A/D ADJUST END=ABORT 244
- Available Modules 246
- Recording 246
- Data Save/Load Function 249
- Optional Math Function 250
- 5 or higher) 251
- Communication Function 253
- Power Supply 253
- Normal Operating Conditions 253
- General Specifications 254
- DU300-11 10 Screw 0.5 s 259
- DU300-12 10 Clamp 0.5 s 259
- Ranges of Indication 263
- 14.8 Alarm Module 271
- 14.9 DI/DO Module 272
- Ethernet Style number: S8 276
- Extension Base 277
- 14.12 Dimensional Drawings 278
- Rear Panel 279
- Sub-unit DS600 280
- Sub-unit DS400 280
- Power Monitor Module 282
- Pulse Input Module 283
- Digital Input Module 283
- DI/DO module/Alarm module 284
- GP-IB module 284
- RS-232-C module 284
- RS-422-A/RS-485 module 285
- Ethernet module 285
- Specifications 286
- Main Menu 287
Verwandte Produkte und Handbücher für Sensoren Yokogawa DR240
Sensoren Yokogawa JUXTA VJCE Bedienungsanleitung
(10 Seiten)
(10 Seiten)
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.132 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern