Yokogawa HIMHART Bedienungsanleitung Seite 13
- Seite / 27
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
The Interface Solution Experts 13
HIM
Smart HART
Loop
Interface and Monitor
HART Device Info
This box displays the identification and revision
information of the monitored HART instrument.
HART Device Status
The HART Device Status box displays the current
status of the monitored HART transmitter. In a small
double-box, the software displays the code (hex
number) associated with the status.
Variables
The device will monitor up to the first four HART
variables sent by your transmitter. This portion of the
screen displays those variables and the Loop Current.
HART Device Range & Limits
This portion of the screen displays the range and the
sensor limits of the monitored HART transmitter.
Display Parameters
The
Display
tab configures the HIM’s LCD display. To
program the Display parameters, change the settings in
the
Display Source
box, then press
Quick Set
. See
the following descriptions of the various sections of the
screen.
Figure 9. Display Tab
Toggle, Variable List
The
Toggle
checkbox causes the HIM to sequentially
display two HART variables in five second increments.
Directly below the
Toggle
checkbox are two list boxes
to select the variables that you would like to be
displayed. Notice that if you select a scaled variable,
it is important to check on the
Scaling
page to verify
that you have set all of the scaling parameters.
Use Custom Label
The
Custom Label
is used to display a calculated or
scaled variable. Clicking the
Use Custom Label
box
causes the HIM to always display the custom label as
Engineering Units (EGUs).
Precision
The
Precision
buttons allow you to change the number
of decimal places displayed by the HIM.
Quick Set
The
Quick Set
button programs the HIM with the
information on the Display page.
Display Format
The HIM reads the dynamic process variable supported
by HART sensors. Generally, the HIM’s LCD displayed
values range from -99999 to 99999. Occasionally,
these process variable values may extend past this
range. To improve the displayed readings, values
below -XXXXX and above XXXXX are translated into
exponential form. Below is an example of the appear-
ance of the display when certain values are sensed.
Value Display
12345 12345
1234500 1.23E06
-500000 -5.00E05
- Smart HART 1
- Interface and Monitor 1
- Table of Contents 2
- About this Manual 3
- Specifications 4
- Configuring the HIM 6
- Installing the HIM 7
- Bench Checking the HIM 9
- PC Configuration Software 10
- HART Parameters 11
- Display Parameters 13
- Alarms Parameters 14
- Analog Outputs Parameters 16
- Custom Curve Parameters 18
- Scaling Parameters 19
- Customer Support 20
- Appendix A: HIM MODBUS 21
- (16 bit integar) 25
- Declaration of Conformity 26
- Warranty Repair – 27
- Non-Warranty Repair – 27
- RETURN PROCEDURES 27
Verwandte Produkte und Handbücher für Sensoren Yokogawa HIMHART
Sensoren Yokogawa EXA SC202 2-Wire Conductivity Transmitter/Analyzer Bedienungsanleitung
(113 Seiten)
(113 Seiten)
Sensoren Yokogawa EXA SC202 2-Wire Conductivity Transmitter/Analyzer Bedienungsanleitung
(72 Seiten)
(72 Seiten)
Sensoren Yokogawa EXA SC202 2-Wire Conductivity Transmitter/Analyzer Bedienungsanleitung
(72 Seiten)
(72 Seiten)
Sensoren Yokogawa EXA ISC202 2-wire Conductivity Transmitter/Analyze Bedienungsanleitung
(64 Seiten)
(64 Seiten)
Sensoren Yokogawa EXAxt SC450 4-Wire Analyzer for Conductivity/Resis Bedienungsanleitung
(68 Seiten)
(68 Seiten)
Allstar Products Group CHALLENGER AC9300 Handbücher
Bedienungsanleitungen und Benutzerhandbücher für Küche Allstar Products Group CHALLENGER AC9300.
Wir stellen 1 PDF-Handbücher Allstar Products Group CHALLENGER AC9300 zum kostenlosen herunterladen nach Dokumenttypen zur Verfügung Bedienungsanleitung
Kommentare zu diesen Handbüchern